Hoverboard Beeping On One Side? [7 Simple Solutions]

Your hoverboard suddenly started beeping on one side may scare you. But don’t worry, in most cases, it doesn’t mean any problems.

Then why is your hoverboard beeping on one side?

The most common reason is that it’s low on charge. Try to recharge it as soon as possible to solve the problem. If that’s not the case, it may be having a balancing issue. In that case, check its self-balancing feature, recalibrate, and look for any disconnected wires or a damaged gyroscope. If none of these work, get your hoverboard to a professional.

Now, let’s know more details about why your hoverboard might be beeping only on one side.

Why Is My Hoverboard Beeping On One Side: Reasons and Solutions

Having a hoverboard beep on one side is a very common problem. Usually, it is a simple fix, but sometimes it can cause serious problems.

In addition, the generalized solution procedure described here applies to most hoverboard brands. However, it is recommended that you check the owner’s manual for specific instructions.

Reason Solution
Low Battery Level Charge the Battery
Speed Warning Adjust Speed Settings
Bad Battery or Charger Replace the battery or the charger
Hoverboard Not Balanced Check Self-Balancing Mode
Recalibrate
Check for Disconnected Wires
Replace Damaged Gyroscope

Reason One: Low Battery Level

The main and the most common reason your hoverboard is beeping on one side is that it may be low on charge. Usually, if the battery is below 10% charge, it warns the user by flashing a red light on one side.

Low Battery Level
Source: Ifixit

Solution: Charge the Battery

To ensure the proper charging of your hoverboard, it’s essential to follow a few guidelines. If you notice a blinking red light, it means that your hoverboard has less than a 10% charge. You should put it on charge without any interruption until it’s fully charged.

However, before you begin charging your hoverboard, it’s crucial to ensure that you’re using the correct charger and following the proper procedure. Start by connecting the charger to the wall and checking that the green indicator light is on before connecting it to the hoverboard.

Also, make sure that the power button on the side of the board’s power box is in the OFF position before plugging it. If you accidentally charged your hoverboard while it was on, leave it in a safe place, turned off, for 24-48 hours. This will help to reset the hoverboard.

Charge the Battery
Source: Tech Caption

Once you’ve completed the above steps, plug the scooter back into the charger while it’s in OFF mode and let it charge. The LED light should change from red to green within fifteen minutes, and you should be able to turn it on.

It’s also crucial to ensure that the temperature of your charging environment is suitable for your hoverboard. Generally, hoverboards charge best in temperatures between 32-104℉ (0-40℃). If the temperature in your charging area is outside this range, it may cause the battery to charge slowly.

If you suspect that the charger is not working, you should get a new one. The price of an average hoverboard charger is only 15-16 dollars.

Reason Two: Speed Warning

If your Jetson hoverboard is beeping on one side, it could be an indication that you have reached the maximum speed limit set for that mode. The beeping sound serves as a warning to slow down and ride safely.

Solution: Adjust Speed Settings

If you are using a hoverboard with adjustable speeds, you can try switching to a different mode to see if the beeping stops. 

To change modes, look for the switch or button on your hoverboard that adjusts the speed settings. If you are currently in “beginner mode” (the slowest), try switching to “intermediate mode” or “advanced mode” (the fastest) to see if the beeping stops.

Reason Three: Bad Battery or Charger

Hoverboard continuously beeping means it has a low battery. But even after charging if the problem persists, then it means a battery or a charger issue.

Solution One: Change the Charger

Try changing the charger and charge the battery again. If this solves your problem, then the charger was the issue. 

But if a new charger did not fix the problem, it can be that the battery is bad.

Solution Two: Change the Battery 

If the battery is faulty, then you have no choice but to replace it. Here is a general guideline-

  • To replace the battery on your hoverboard, start by making sure the device is completely powered off and unplugged from any outlets. 
  • Then, flip the Swagtron so that the footpads are facing the ground.
  • Next, unscrew the screws on the side of the hoverboard that is now facing upwards. 
  • After that, slowly lift the backside cover. Both sides lift up the same way, but the motherboard is under one side and the battery is under the other. 
  • Detach the four cables connected to the cover by pinching the connector clips and pulling the cables out. 
  • There are three cables on the motherboard side: two red cables with white connectors and one white cable with a white connector. On the battery side, there is one yellow cable with a black connector.
  • After detachment, you should be able to completely remove the backside cover. Unscrew the four screws attaching the battery to the base of the hoverboard.
  • Detach the two cables connecting the battery to the hoverboard by pinching the connector clips and pulling the cables apart. 
  • There is one red and black cable with a yellow connector and one blue cable with a black connector. 
  • Finally, remove the battery by pulling it out from under the cables.

Once you have the old battery removed, you can replace it with a new one by following these steps in reverse order. Be sure to connect all cables securely and screw in all screws tightly to ensure proper functioning of the hoverboard.

Reason Four: Hoverboard Not Balanced

If the issue was not with the battery or the charger, then it could be because the hoverboard is not balanced. Follow the procedures below for a proper diagnosis.

Solution One: Check the Self-Balancing Mode

To fix the balance of your hoverboard, the first step is to ensure that it’s in self-balancing mode.

Check the Self-Balancing Mode
Source: Electric Unicycle Forum

Move the hoverboard to a flat surface and wait a few minutes before attempting to ride it again. Make sure both of your feet are placed properly on the pedals so that it can detect them accurately.

It’s also important to check that no other objects are obstructing the pedals. Moreover, hoverboards with self-balancing sensors can malfunction if used sideways or on slopes.

Solution Two: Recalibrate the Hoverboard

Sometimes, you will need to perform calibration again if the issue persists. In this process, the hoverboard’s gyroscope and sensor are reset. Here are the steps:

  • Turn off the hoverboard by pressing and holding the power button until it shuts down.
  • Ensure that the foot pedals are level with the ground and with each other.
  • For ten seconds, hold down the power button until you hear a beep and see the LED lights flash.
  • Continue holding the power button until the hoverboard turns off completely.
  • Leave the hoverboard in the off position for several seconds.
  • For the hoverboard to turn on, press the power button again.
  • You can check if the problem has been resolved by testing the hoverboard.

If the problem persists even after doing it once, you can repeat the recalibration process up to five times to fully reset and recalibrate the hoverboard.

Solution Three: Check for Disconnected Wires

If recalibration didn’t do it, then it may indicate an internal problem, probably a disconnected wire in the circuit. If the hoverboard’s wires are disconnected, it may not function properly. 

After removing the outer shell, check if any cables are disconnected. If all cables are connected, disconnect and reconnect them all.

Solution Four: Replace the Damaged Gyroscope

If the hoverboard still does not balance itself correctly, a damaged gyroscope could be the issue. Replacing the gyroscope to solve the problem.

Here are the instructions to replace the gyroscope in a hoverboard:

  • Turn off the hoverboard and unplug it from any outlets.
  • Flip the hoverboard over so that the footpads face the ground.
  • Unscrew the screws with a screwdriver located on the side of the hoverboard that’s facing upwards.
  • Carefully lift the backside cover and detach the four cables connected to the cover.
  • Find the gyroscope, which is a rectangular blue circuit board atop a white base closest to the wheel.
  • Detach the four cables connecting the gyroscope to the hoverboard and unscrew the screws that are connecting the blue gyroscope to the white plastic holding piece.
  • Grasp the white plastic holder piece gently and remove the blue gyroscope from it. Cut the plastic cable tie that is holding the cables together.
  • Replace the old gyroscope with the new one and carefully reassemble the hoverboard by following the above steps in reverse order.
  • After reassembling, check if the hoverboard is balancing properly.

If the hoverboard is still unbalanced after replacing the gyroscope, repeat all the above steps with the gyroscope on the other wheel.

What to Do If the Hoverboard Still Beeps on One Side?

If none of the previously mentioned solutions resolve your hoverboard’s issue, the  problem may be related to the device’s hardware or software. 

In this case, it’s best to seek professional assistance to ensure that the issue is properly diagnosed and resolved.

The Best Way to Take Care of Your Hoverboard

Taking good care of your hoverboard can help extend its lifespan and ensure that it remains in good working condition for as long as possible. Here are some tips for caring for your hoverboard:

  • Extreme temperatures or humidity can damage the battery and other components of your hoverboard. Avoid storing your hoverboard in direct sunlight or areas with high humidity.
  • Cleaning your hoverboard is very important. Regularly wipe down your hoverboard with a clean, dry cloth to remove any dirt or debris. You can also use a damp cloth to clean the footpads and other areas of the hoverboard that get dirty.
  • Charge your hoverboard according to the manufacturer’s instructions. Avoid overcharging your hoverboard or leaving it plugged in for extended periods, as this can damage the battery.
  • Hoverboards are designed for smooth, flat surfaces. Avoid riding your hoverboard on rough terrain or uneven surfaces, as this can cause damage to the wheels and other components.
  • Check your hoverboard for any signs of damage or wear and tear, such as cracks in the body or worn-down wheels. To prevent further damage, address any issues as soon as possible.
  • Most hoverboards have weight limits, so make sure to check the manufacturer’s recommendations before riding your hoverboard. Exceeding the weight limit can damage the hoverboard and potentially cause accidents.

By following these tips, you can help keep your hoverboard in good condition and ensure that it lasts for many years to come.

Frequently Asked Questions (FAQs):

Why is one side of my hoverboard not working?

A faulty gyroscope could be the reason why one side of your hoverboard is not working. This can result in the hoverboard spinning in circles or one side not responding properly to user input. In such a case, the gyroscope would need to be replaced with a new one.

Why is one side of my hoverboard flashing blue?

Low battery. When the hoverboard is flashing a blue light it could be due to the battery being low on charge. Recharge the hoverboard battery as soon as possible.

Why is my hoverboard beeping and not turning off?

If your hoverboard is continuously beeping and not turning off, it could be due to a technical malfunction. In such a situation, it is recommended to take the hoverboard and keep it in the backyard or garage to allow the battery to drain completely. This process might take some time, but once the battery is drained to zero percent, the hoverboard will automatically turn off.

Conclusion

Although there are many hoverboard brands, a hoverboard beeping on one side more or less means the same thing. However, if the solutions described in this article don’t work for you, get your hoverboard to your dealer and have them look at it.

Leave a Comment